Publications

We have compared the total boron content and hole carrier concentration values obtained from various destructive and non-destructive quantification methods in boron doped nano-crystalline diamond films prepared over a range of doping levels, using microwave plasma enhanced chemical vapour deposition. Destructive secondary-ion mass spectrometry and relatively unreported glow discharge optical emission spectrometry were complemented by non-destructive Raman, spectroscopic ellipsometry and van der Pauw Hall measurements. Measurement techniques are discussed, including details of the glow discharge optical emission spectrometry technique; use of different laser powers and wavelengths, fitting parameters for Raman spectroscopy, and improved ellipsometry modelling. Finally, measured values are compared and discussed regarding their viability for estimation of total boron and electrically active boron in doped nano-crystalline diamond layers.

In this work, a unified numerical model is used to determine the melting thresholds and to investigate the early stages of melting of several crystalline semiconductors (Si, Ge, GaAs, CdTe and InP) irradiated by nanosecond laser pulses. A molten fraction approach is used for continuous transition over the melting point. The results are compared with previously published theoretical and experimental data. A survey on the thermophysical and optical properties of the selected materials has been carried out to gather the most relevant data on temperature dependent properties for the solid and liquid states of these semiconductors where such data are available. A generalization of the obtained results is established that enables evaluation of the melting thresholds for different semiconductors based on their properties and irradiation conditions (laser wavelength, pulse duration).

We present the laser characteristics of a 5 at.% Tm:YLF crystal using a modular setup at cryogenic temperatures emitting around 2 µm. Continuous-wave laser operation was achieved by pumping the laser crystal using a Volume Bragg Grating-stabilized laser diode emitting at 793 nm. A maximum output power of 6.5 W was achieved at 80 K corresponding to a slope efficiency of 66.0% with respect to the absorbed power with excellent beam quality.

For the first time, a dynamic beamshaping technology has been utilized for the efficient production of periodic nanostructures on top of AlTiN coating to enable dry machining without costly and environmentally hazardous cutting fluids. First, a variety of periodic nanostructures with periods in a range of 740–273 nm were produced utilizing different wavelengths. Additionally, beamshaping technology increased productivity by 4008% up to 105 cm2 min−1 by shaping the Gaussian beam into a rectangular beam of 500 × 30 µm. To simulate the application load and resulting heat production during manufacturing, friction analysis was performed at room and elevated temperature to 500°C. The analysis revealed a significant reduction in the friction coefficient – up to 27% and 19% at room temperature and 500°C, respectively. The combination of these results demonstrates that the proposed method can be scaled up for the mass production of functionalized machining tools for dry machining.

Many different fields benefit from the usage of light sources emitting in the mid-infrared wavelength range (2–10 µ m). A rising need for precise and fast sources in the mid infrared (mid-IR) is reflected in the development of a high-power, picosecond mid-IR source capable of generation at high repetition rates. In this work, we present the optimization of an optical parametric generator, pumped by a 3 W portion of total power of the Yb:YAG thin-disk laser (1.3 ps, 90 kHz, 90 W) by comparing a single-pass and double-pass arrangement output parameters in terms of output power dependences on input power, efficiency, beam profiles, stability, and spectra. The output tunability of both arrangements spanned from 1459 nm to 2891 nm, with the upper limit being influenced by the limited transmission of the dichroic components used in the setup above 2700 nm. It was shown that the double-pass arrangement increases the output power, from 17 mW in the single-pass arrangement to 193 mW in the double-pass arrangement at 1459 nm, resulting in over ten-fold output power increase.

Nuclear fusion between protons and boron-11 nuclei has undergone a revival of interest thanks to the rapid progress in pulsed laser technology. Potential applications of such reaction range from controlled nuclear fusion to radiobiology and cancer therapy. A laser-driven fusion approach consists in the interaction of high-power, high-intensity pulses with H- and B-rich targets. We report on an experiment exploiting proton-boron fusion in CN-BN targets to obtain high-energy alpha particle beams (up to 5 MeV) using a very compact approach and a tabletop laser system with a peak power of ~10 GW, which can operate at high-repetition rate (up to 1 kHz). The secondary resonance in the cross section of proton-boron fusion (~150 keV in the center-of-mass frame) is exploited using a laser-based approach. The generated alpha particles are characterized in terms of energy, flux, and angular distribution using solid-state nuclear-track detectors, demonstrating a flux of ~105 particles per second at 10 Hz, and ~106 per second at 1 kHz. Hydrodynamic and particle-in-cell numerical simulations support our experimental findings. Potential impact of our approach on future spread of ultra-compact, multi-MeV alpha particle sources driven by moderate intensity (1016-1017 W/cm2) laser pulses is anticipated.

Pulsed laser crystallization is an efficient annealing technique to obtain polycrystalline silicon or germanium films on non-refractory substrates. This is important for creating “flexible electronics” and can also be used to fabricate thin-film solar cells. In this work, near- and mid-infrared femtosecond and picosecond laser pulses were used to crystallize a Ge/Si multilayer stack consisting of alternating amorphous thin films of silicon and germanium. The use of infrared radiation at wavelengths of 1030 and 1500 nm with photon energies lower than the optical absorption edge in amorphous silicon allowed obtaining selective crystallization of germanium layers with a single laser shot. The phase composition of the irradiated stack was investigated by the Raman scattering technique. Several non-ablative regimes of ultrashort-pulse laser crystallization were found, from partial crystallization of germanium without intermixing the Ge/Si layers to complete intermixing of the layers with formation of GexSi1-x solid alloys. The roles of single- and two-photon absorption, thermal and non-thermal (ultrafast) melting processes, and laser-induced stresses in selective pico- and femtosecond laser annealing are discussed. It is concluded that, due to a mismatch of the thermal expansion coefficients between the adjacent stack layers, efficient explosive solid-phase crystallization of the Ge layers is possible at relatively low temperatures, well below the melting point.

The generation, detection, and quantification of high-energy proton spectra that are produced from laser-target interaction methodologies is a field of increasingly growing popularity over the last 20 years. Generation methods such as target normal sheath acceleration or similar allow for collimated laminar ion beams to be produced in a compact environment through the use of short-burst terawatt lasers and are a growing field of investment. This project details the development and refinement of a python-based code to analyze time-of-flight ion spectroscopy data, with the intent to pinpoint the maximum proton energy within the incident beam to as reliable and accurate a value as possible within a feasible processing time. TOF data for 2.2 × 1016 W/cm2 intensity laser shots incident on a 2 mm Cu target that were gathered from the PERLA 1 kHz laser at the HiLASE center were used as training and testing data with the implementation of basic machine learning techniques to train these methods to the data being used. These datasets were used to ensure more widely applicable functionality, and accurate calculation to within 1% accuracy of an assumed correct value was seen to be consistently achievable for these datasets. This wider functionality indicates a high level of accuracy for previously unseen TOF datasets, regardless of signal/noise levels or dataset size, allowing for free use of the code in the wider field.

This paper describes reduction in noise, vibrations, total and tooth-to-tooth, and longwave transmission errors, total and tooth-to-tooth composite errors, and radial runout of spur gears by imparting them flank modifications and their combinations by a non-contact advanced finishing process referred to as pulsed electrolytic dissolution. Eight spur gears were modified using innovatively developed 5 cathode gears and apparatus by imparting them 5 flank modifications (i.e. tip relief, root relief, end relief, profile crowning, lead crowning) individually and their 4 selected combinations. Vibrations at all rotational speeds and noise at 900 and 1200 rpm are reduced for all modified spur gears at all the values of applied loads. End relieved spur gear showed maximum reductions in noise and vibrations by 5 dBA and 3.77 m/s2 respectively for 1200 rpm speed. Reduction amount in noise and vibrations of modified gears increase with rotary speed. Lead crowned gear showed maximum reductions of 146 µm in total transmission error, 109 µm in total composite error, and 102 µm in radial runout. End relieved gear showed maximum reductions of 37 µm in tooth-to-tooth and 139 µm longwave transmission errors. Tip relieved, and tip and root relieved gear showed maximum reduction of 121 µm in tooth-to-tooth composite error. This work proves that the developed non-contact process can very effectively impart different flank modifications individually and their combinations to spur gears without any twist error. Lead crowning, end relieving, tip relieving, and tip and root relieving are main flank modifications that significantly improve functional performance characteristics of spur gears. It will result in their enhanced operating performance and service life, which will help their manufacturers and end-users.

Optical enhancement cavities enabling laser pulses to be coherently stacked in free space are used in several applications to enhance accessible optical power. In this study, we develop an optical cavity that accumulates harmonically mode-locked laser pulses with a self-resonating mechanism for X-ray sources based on laser-Compton scattering. In particular, a Fabry-Perot cavity composed of 99% reflectance mirrors maintained the optical resonance in a feedback-free fashion for more than half an hour and automatically resumed the accumulation even if the laser oscillation was suspended. In contrast to conventional optical enhancement cavity systems with a dedicated feedback controller, this characteristic is highly beneficial in practical applications, such as for laser-Compton scattering X-ray sources. Lastly, upscaling and adoption of the proposed system might improve the operability and equipment use of laser Compton-scattering X-ray sources.

Nonlinear optical response of materials exposed to strong nonresonant light fields leads to production of high energy photons whose spectra contain fingerprints of the coherent electron dynamics in the material. In this paper we investigate how the high harmonic spectra generated in crystalline silicon are linked to specific properties of its band structure. By comparing the polarization anisotropy of high harmonic spectra for two distinct frequencies of the driving pulses we show that the anisotropy has two sources. When driven by mid-infrared light, the signal at specific photon energies is enhanced by the presence of Van Hove singularities in the joint density of states of silicon. With near-infrared driving pulses, in contrast, the high harmonic yield is mainly influenced by the anisotropy of the reduced mass of electron-hole pair, which is related to the nonresonant excitation probability. The experimental results are compared with numerical calculations using time-dependent density functional theory.

The novel method of the thermally-induced polarization changes driven power losses (TIPCL) analysis in the complex laser systems has been developed. The measurement has been tested on the amplifier chain of the 100 J / 10 Hz laser system ‘Bivoj’ operated at HiLASE Centre. By the usage of the measured non-uniform Mueller matrix of the amplifier chain, the optimization of the ideal input and output polarization state has been calculated numerically. The results of the optimization have been applied to the laser system, thus reducing the TIPCL from originally observed more than 33% to 7.9% for CW beam and to 9% for pulsed laser beam, respectively. To the best of our knowledge, this result represents the most efficient TIPCL suppression method for complex laser systems so far. The method also allows the definition of the ideal fully polarized non-uniform pre-compensation of input beam consequently suffering from zero TIPCL.

Energy relaxation in a thin molybdenum film exposed to a single laser pulse (wavelength 400 nm, pulse duration 200 fs at FWHM) has been investigated numerically. For this purpose, a two-temperature model was used accounting for the optical and thermodynamical properties of molybdenum deposited on a selection of substrates. The effect of the substrate on laser-induced film heating has been studied for the cases of fused silica, silicon, soda-lime glass as well as for a free-standing film. For a fused silica substrate, the calculated melting threshold fluence is in a good agreement with thickness-dependent experimental data available in literature. It has been found that, for Mo films with the thickness 107 nm, the softening point of the fused silica substrate is exceeded already at the Mo melting threshold fluence. This suggests the possibility of substrate damage related to glass deformation. The melting dynamics of the Mo film and the effects of energy transfer from the irradiated film to the substrate are discussed based on the modeling results.

The fluctuation–magnification effect on the peak intensity of a laser pulse caused by the nonlinear Kerr effect in the chirped volume Bragg grating (CVBG) compressor is investigated experimentally for a high-energy, thin-disk, chirped pulse amplification system. The nonlinear Kerr effect occurs at the blue end, and the accumulated nonlinear phase shift (B-integral) in the CVBG rises with the increase of laser pulse energy. Experiments show that small fluctuations in peak power of uncompressed pulses cause increasing of the temporal fluctuation and spatial fluctuation due to high Kerr-nonlinearity in the CVBG when B-integral is larger than π. Thus the initial fluctuation would be magnified by the CVBG compressor.

In the article, the author team presents an adaptive optics (AO) system for a 1.94-µm laser source. The system consists of a home-made Shack–Hartmann wavefront sensor and silver-coated bimorph deformable mirror operating in a closed-loop control scheme. The wavefront sensor used an uncooled vapor phase deposition PbSe focal-plane array for the actual light sensing. An effect of thermal afterimage was found to be reducing the centroid detection precision significantly. The effect was analyzed in detail and finally has been dealt with by updating the background calibration. System stability was increased by reduction of control modes. The system functionality and stability were demonstrated by improved focal spot quality. By replacing some of the used optics, the range of the demonstrated mid-IR AOS could be extended to cover the spectral range of 1–5 µm. To the best of the authors’ knowledge, it is the first AO system built specifically for mid-IR laser wavefront correction.

Laser-induced periodic surface structures (LIPSS) formation on the surface of mono-crystalline silicon is reported for a specific fabrication regime of large-area structuring. Using a femtosecond laser at 1030 nm wavelength, a particular range of fluence and beam overlap in two-dimensional scanning scheme has been identified where LIPSS-covered areas organize into stripes perpendicular to the scanning direction. The stripes, where the LIPSS appear, are regularly spaced and located in between the centers of two subsequent Gaussian pulses while the regions receiving the peak pulse fluence are free of LIPSS. The formation of the LIPSS stripes is examined by analyzing local integrated fluence, N-on-1 pulse damage geometry and thresholds of modifications. Processes at play in the generation of such stripes of LIPSS are discussed and an explanation based on interpulse feedback from amorphized areas is proposed.

This book covers the fundamentals of different laser-based manufacturing and processing, namely laser shock peening, laser micromachining, laser cleaning, cladding, remelting, laser honing, and other several aspects of lasers. The book discusses the general laser interaction with different materials. The application of laser-based post-processing of additive manufacturing and repair engineering is reported. It also provides the reader with mechanism of lasers in manufacturing and recent developments in tools, technologies, controls, and operations.